Shanxi electroforming signage manufacturer design-Metal signage manufacturer

by:ShunDing     2020-07-29
Foshan ultra-thin nickel standard manufacturers design

More than 95% of the badges are stamping and die casting processes, these two processes can be used to make some badges with a very three-dimensional feeling, especially die-casting is suitable for Super three-dimensional or 3D three-dimensional badges. Industry metal products industry also encountered some difficulties in the development process, such as single technology, low technical level, lack of equipment, shortage of talents, etc. , which restricted the development of metal products industry. To this end, we can improve the development of the metal products industry by improving the technical level of enterprises, introducing technical equipment, and cultivating suitable talents. In 2009, products in the metal products industry will tend to be more and more diversified, the technical level of the industry will be higher and higher, the product quality will be steadily improved, and the competition and market will be further rationalized. Hardware products auxiliary and accessory finished products used in daily life and industrial production.

sand mold casting: low cost, small batch, can process complex shapes, but may require a large number of post-processing processes. Investment casting/lost wax casting: this processing method has high continuity and degree, and metal products can also be used to process complex shapes. On the premise of relatively low processing cost, it can achieve perfect surface effect and is suitable for mass production.

bending: an economical production process for processing any form of sheet, Rod and tubular materials. Continuous binding and forming: feed metal sheets between pressure rollers to obtain metal shapes with continuous length and consistent cross section. Similar to the extrusion process, but the wall thickness of the processed components is limited, only a single wall thickness can be obtained. Only on the premise of mass production, the processing cost is reasonable. The stamped metal sheet is placed between the male die and the female die and is pressed and formed for processing hollow shapes, and the depth can be deep or shallow.

adhesive backing is not suitable for signs like split signs or signs with small lines. Adhesive backing has strong adhesion, good retention, strong temperature resistance and good waterproof performance, it is an environmentally friendly chemical. Four-dimensional glue commonly used in digital products, household appliances, furniture, mechanical equipment, car key chains and other products is a glue with strong viscosity among these common glues.

The design of Foshan ultrathin nickel standard factory
influenced by its chemical structure, the chemical structure is stable compared with aluminum material. Under the same conditions and environment, stainless steel is not prone to oxidative rust deformation. Therefore, most of the users who need to keep the signs bright and beautiful for a long time under the conditions of long-term outdoor exposure to rainwater or wet, cold and high temperature environment choose to use stainless steel materials. In short, the stainless steel sign is characterized by durability and not easy to deform. Characteristics of aluminum signs: in terms of manufacturing process, the manufacturing of aluminum signs is much simpler and more convenient than that of stainless steel signs.

SiMnMo series Graphite Steel is characterized by high Si content. Under the action of strong graphitization element Si, some carbon exists in graphitization state, the steel has self-lubricating effect, high bite resistance, good machinability and wear resistance, small heat treatment deformation and stable size. SiMnMo steel is used to make bending, stretching and punching dies with strict surface quality requirements, which can significantly improve the quality of punching parts.

such as 6W6Mo5Cr4V2, the specific heat treatment process is quenching heating temperature 1160-1180 ℃, after cooling, after 550- Tempering at 570 ℃ for three times, hardness Rc60- 63, used for cold extrusion punch or cold heading punch can double the service life. Matrix Steel: Matrix Steel is another way to improve the toughness of high speed steel. Compared with high speed steel, Matrix Steel has few excess carbides and fine carbide particles, the distribution is uniform, so the impact toughness and fatigue strength are better than that of high speed steel, while maintaining good wear resistance. Matrix Steel successfully developed and popularized in China. The basic principle of electroforming is to use the original mold made according to the required shape as the cathode, use the electroforming material as the anode, and put it into the same metal salt solution as the anode material to pass direct current. Under the action of electrolysis, a metal electroforming layer is gradually deposited on the surface of the original mold, and the metal electroforming layer is taken out of the solution after reaching the required thickness, and the electroforming layer is separated from the original mold, the metal parts corresponding to the shape of the original mold are obtained. The stability of nickel plating layer in air is very high. Due to the strong passivation ability of metal nickel, a very thin passivation film can be rapidly formed on the surface to resist the corrosion of atmosphere, alkali and some acids.

Foshan ultrathin nickel standard factory design
receiving engineering drawings according to CDR, AI or cad format engineering drawings provided by customers, according to size, color, thickness, glue and other process requirements to order, logo design in the drawings any line size width shall not be less than 0. 25mm (For example, the I word is only 0. , Then the drawings must be changed, or communicate with the customer to change the size, otherwise the size is too small, it is difficult to take it down during the shipping process, resulting in the improvement of defective products) After confirming the drawings, we will first make samples and send samples to the customer for confirmation. After confirmation by the customer, the order will be made.


custom name tags are required in the manufacture of almost every product and custom name tags Journalism is one of the most common machines.
For details on Journalism, see DongGuan ShunDing Hardware Products Co., LTD at ShunDing Metal Nameplate.
Journalism provider at ShunDing Metal Nameplate offers a wide variety of in many options. quality is absolutely ensured if you choose us. welcome to visit our factory.
The above are only part of the examples regarding Journalism, for more information, please click here ShunDing Metal Nameplate.
Custom message
Chat Online
Chat Online
Chat Online inputting...
Joey
Joey
Echo
Echo
Alen.Chen
Alen.Chen
Sign in with: